Discussion:
Ethernet card does not work with FC2
Alberto M R Davila
2004-07-21 00:56:30 UTC
Permalink
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3) and
the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting partitions)
but it does not work as well... curiously during boot the eth0 is loaded
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled to
allow only SSH connections... btw, my sound card was not recognized after
installation as well, the test failed... any tips how I could conifgure
the eth0 manually ? Everything used to work fine when I was using FC1 in
the same laptop ;-)

Thanks for any tips you may send.

Cheers, Alberto





__________________________________
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 01:37:32 UTC
Permalink
Yes, I use static IP address and not DHCP... I was using FC1 nicely (with
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should run
nice as well... :-(

Will try your suggestion in case I don?t get any further useful tips.

Thanks, Alberto
Hey,
--my 2 cents--
I'm assuming that you dont have dhcp setup for that, which makes
sense. I jumped over to the toshiba satellite and the 4600 isnt sold
anymore (least I didnt see it in the product area of their website).
First thing I would probably do *I'm no expert, but I can get things
done* is go here http://www.lnxbbc.com/ and d/l that little 50meg
distro that runs from cd. It has a simple network setup utility and
if it can get you connected you know its just a setting in fedoracore.
I'd really have to know more about the actual hardware to help you
anymore. Dont know if this will help you any.
-Matt
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
__________________________________
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
http://promotions.yahoo.com/new_mail
--
fedora-list mailing list
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - Send 10MB messages!
http://promotions.yahoo.com/new_mail
James A. Giseburt
2004-07-21 06:27:21 UTC
Permalink
Good Day!

I also have a Toshiba Satellite Pro 4600. As you stated, everything
worked well with FC1. Not so with FC2.

I am not having your problem with eth0 (the built-in ethernet adapter).
I do have an alias in /etc/modprobe.conf for that adapter (alias eth0
e100), but other than that it works.

I am also having the problems that you describe with sound. I haven't
been able to figure that out yet. I've checked all of the sound
settings that I can find and I'm still looking. At this point, it would
be nice to hear a simple beep, let alone music or some other audio.

My only other problem is that my Cisco Aironet 350 PC Card doesn't
work. It worked in FC1, but I haven't been able to get it to work with
FC2. The system recognizes the card, but I haven't been able to
activate the interface. I'm stumped at this point. Other people say
that they have gotten this card to work, but not me. I've resorted to
an old D-Link card (it pops right up).

Sorry I haven't been of any help, but I just wanted to let you know that
you are not alone.


Jim

James A. Giseburt
Information Systems Manager E-mail: giseburt at molineschools.org
Moline School District No. 40 Voice : 309.743.8990
2515 - 41st Street Fax : 309.743.8996
Moline, IL 61265 Web : http://www.molineschools.org
Post by Alberto M R Davila
Yes, I use static IP address and not DHCP... I was using FC1 nicely (with
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should run
nice as well... :-(
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
James A. Giseburt
2004-07-21 06:27:21 UTC
Permalink
Good Day!

I also have a Toshiba Satellite Pro 4600. As you stated, everything
worked well with FC1. Not so with FC2.

I am not having your problem with eth0 (the built-in ethernet adapter).
I do have an alias in /etc/modprobe.conf for that adapter (alias eth0
e100), but other than that it works.

I am also having the problems that you describe with sound. I haven't
been able to figure that out yet. I've checked all of the sound
settings that I can find and I'm still looking. At this point, it would
be nice to hear a simple beep, let alone music or some other audio.

My only other problem is that my Cisco Aironet 350 PC Card doesn't
work. It worked in FC1, but I haven't been able to get it to work with
FC2. The system recognizes the card, but I haven't been able to
activate the interface. I'm stumped at this point. Other people say
that they have gotten this card to work, but not me. I've resorted to
an old D-Link card (it pops right up).

Sorry I haven't been of any help, but I just wanted to let you know that
you are not alone.


Jim

James A. Giseburt
Information Systems Manager E-mail: giseburt at molineschools.org
Moline School District No. 40 Voice : 309.743.8990
2515 - 41st Street Fax : 309.743.8996
Moline, IL 61265 Web : http://www.molineschools.org
Post by Alberto M R Davila
Yes, I use static IP address and not DHCP... I was using FC1 nicely (with
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should run
nice as well... :-(
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
John Morrison
2004-07-21 08:10:15 UTC
Permalink
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3) and
the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting partitions)
but it does not work as well... curiously during boot the eth0 is loaded
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled to
allow only SSH connections... btw, my sound card was not recognized after
installation as well, the test failed... any tips how I could conifgure
the eth0 manually ? Everything used to work fine when I was using FC1 in
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,

I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.

--
John
jludwig
2004-07-21 16:40:03 UTC
Permalink
Post by John Morrison
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3) and
the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting partitions)
but it does not work as well... curiously during boot the eth0 is loaded
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled to
allow only SSH connections... btw, my sound card was not recognized after
installation as well, the test failed... any tips how I could conifgure
the eth0 manually ? Everything used to work fine when I was using FC1 in
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
Something simple. Does your netmask match the network netmask?
--
jludwig <wralphie at comcast.net>
jludwig
2004-07-21 16:40:03 UTC
Permalink
Post by John Morrison
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3) and
the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting partitions)
but it does not work as well... curiously during boot the eth0 is loaded
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled to
allow only SSH connections... btw, my sound card was not recognized after
installation as well, the test failed... any tips how I could conifgure
the eth0 manually ? Everything used to work fine when I was using FC1 in
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
Something simple. Does your netmask match the network netmask?
--
jludwig <wralphie at comcast.net>
Alberto M R Davila
2004-07-21 10:11:17 UTC
Permalink
Hi,

The "network device control" is like this:

Status Device Nickname
Active eth0 eth0

Looks OK but does * not * work ... how I could configure manually ?

Thanks, Alberto
Post by Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
http://promotions.yahoo.com/new_mail
Andrea Marin
2004-07-21 10:47:14 UTC
Permalink
Hi Alberto,

you can configure all your network-interface in
/etc/sysconfig/network-script.

In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option

this is an example:

# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol


Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
John Morrison
2004-07-21 11:04:26 UTC
Permalink
Post by Andrea Marin
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
Alberto,

try the following as root:
vim /etc/sysconfig/networking/devices/ifcfg-eth0

John
John Morrison
2004-07-21 11:04:26 UTC
Permalink
Post by Andrea Marin
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
Alberto,

try the following as root:
vim /etc/sysconfig/networking/devices/ifcfg-eth0

John
Andrea Marin
2004-07-21 10:47:14 UTC
Permalink
Hi Alberto,

you can configure all your network-interface in
/etc/sysconfig/network-script.

In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option

this is an example:

# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol


Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
Alberto M R Davila
2004-07-21 10:39:14 UTC
Permalink
Hi,

Good and bad to know I am not alone ! ;-)

I just checked my /etc/sysconfig/hwconf:

class: NETWORK
bus: PCI
detached: 0
device: eth0
driver: e100
desc: "Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller"
network.hwaddr: 00:00:39:DE:29:3F
vendorId: 8086
deviceId: 2449
subVendorId: 8086
subDeviceId: 3013
pciType: 1
pcidom: 0
pcibus: 2
pcidev: 8
pcifn: 0
-

-
class: NETWORK
bus: PCMCIA
detached: 96
device: eth1
driver: orinoco_cs
desc: "Intersil PRISM2 11 Mbps Wireless Adapter"
vendorId: 0156
deviceId: 0002
function: 0
slot: 0

Again apparently looks OK, unless the real experts let me know about any
problems.

I am missing my FC1 now, without eth0 up and working I cannot do my stuff.

Thanks for any further tips you may send.

Cheers, Alberto
Post by James A. Giseburt
Good Day!
I also have a Toshiba Satellite Pro 4600. As you stated, everything
worked well with FC1. Not so with FC2.
I am not having your problem with eth0 (the built-in ethernet adapter).
I do have an alias in /etc/modprobe.conf for that adapter (alias eth0
e100), but other than that it works.
I am also having the problems that you describe with sound. I haven't
been able to figure that out yet. I've checked all of the sound
settings that I can find and I'm still looking. At this point, it would
be nice to hear a simple beep, let alone music or some other audio.
My only other problem is that my Cisco Aironet 350 PC Card doesn't
work. It worked in FC1, but I haven't been able to get it to work with
FC2. The system recognizes the card, but I haven't been able to
activate the interface. I'm stumped at this point. Other people say
that they have gotten this card to work, but not me. I've resorted to
an old D-Link card (it pops right up).
Sorry I haven't been of any help, but I just wanted to let you know that
you are not alone.
Jim
James A. Giseburt
Information Systems Manager E-mail: giseburt at molineschools.org
Moline School District No. 40 Voice : 309.743.8990
2515 - 41st Street Fax : 309.743.8996
Moline, IL 61265 Web : http://www.molineschools.org
Post by Alberto M R Davila
Yes, I use static IP address and not DHCP... I was using FC1 nicely
(with
Post by Alberto M R Davila
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should
run
Post by Alberto M R Davila
nice as well... :-(
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium
3)
Post by Alberto M R Davila
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by Alberto M R Davila
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled
Post by Alberto M R Davila
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1
Post by Alberto M R Davila
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
Alberto M R Davila
2004-07-21 11:14:25 UTC
Permalink
Thanks Andrea,

My "ifcfg-eth0" is like this:

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no

When I "ping" to a machine in the intranet I got this:

[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
--- LOCAL.MACHINE ping statistics ---
10 packets transmitted, 0 received, +9 errors, 100% packet loss, time
8998ms
, pipe 5:

In other words, it is not working yet :-(

Any further tips ?

Thanks, Alberto
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - 100MB free storage!
http://promotions.yahoo.com/new_mail
Andrea Marin
2004-07-21 11:58:50 UTC
Permalink
But when you lunch as root:

#ifconfig eth0

what happen?

If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.

But the service network is started?
/etc/rc.c/init.d/network status

the answer maybe is like this

Configured devices:
lo eth0
Currently active devices:
lo eth0

If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
must bring up whit the command :

/etc/rc.c/init.d/network start

Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.

Bye Andrea
Post by Alberto M R Davila
Thanks Andrea,
# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no
[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
Scot L. Harris
2004-07-21 12:58:54 UTC
Permalink
Post by Andrea Marin
#ifconfig eth0
what happen?
If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.
But the service network is started?
/etc/rc.c/init.d/network status
the answer maybe is like this
lo eth0
lo eth0
If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
/etc/rc.c/init.d/network start
Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.
Bye Andrea
And once have the above excellent advice working you need to make sure
you have your default gateway configured correctly and valid DNS entries
in /etc/resolv.conf.

To check your gateway run:

netstat -rn

There should be a line with UG in it that is the default gateway. This
should point to your LANs gateway, depending on setup this could be the
cable modem or a router that sits in front of the cable modem.

In /etc/resolv.conf there should be at least one hopefully 2 or 3
nameserver entries followed by IP addresses of your ISPs DNS servers.

Start by getting basic LAN connectivity and then check for default
gateway and DNS configuration.
--
Scot L. Harris
webid at cfl.rr.com

To criticize the incompetent is easy; it is more difficult to criticize
the competent.
Scot L. Harris
2004-07-21 12:58:54 UTC
Permalink
Post by Andrea Marin
#ifconfig eth0
what happen?
If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.
But the service network is started?
/etc/rc.c/init.d/network status
the answer maybe is like this
lo eth0
lo eth0
If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
/etc/rc.c/init.d/network start
Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.
Bye Andrea
And once have the above excellent advice working you need to make sure
you have your default gateway configured correctly and valid DNS entries
in /etc/resolv.conf.

To check your gateway run:

netstat -rn

There should be a line with UG in it that is the default gateway. This
should point to your LANs gateway, depending on setup this could be the
cable modem or a router that sits in front of the cable modem.

In /etc/resolv.conf there should be at least one hopefully 2 or 3
nameserver entries followed by IP addresses of your ISPs DNS servers.

Start by getting basic LAN connectivity and then check for default
gateway and DNS configuration.
--
Scot L. Harris
webid at cfl.rr.com

To criticize the incompetent is easy; it is more difficult to criticize
the competent.
Andrea Marin
2004-07-21 11:58:50 UTC
Permalink
But when you lunch as root:

#ifconfig eth0

what happen?

If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.

But the service network is started?
/etc/rc.c/init.d/network status

the answer maybe is like this

Configured devices:
lo eth0
Currently active devices:
lo eth0

If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
must bring up whit the command :

/etc/rc.c/init.d/network start

Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.

Bye Andrea
Post by Alberto M R Davila
Thanks Andrea,
# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no
[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
Alberto M R Davila
2004-07-21 11:31:04 UTC
Permalink
Hi John,

It is exactly as in /etc/sysconfig/network-scripts:

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no

Should I try a source (which one ?) from fedora site and try a fresh
installation by "make" and "make install" ?

Thanks, Alberto
Post by John Morrison
Post by Andrea Marin
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0"
and
Post by Andrea Marin
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
Alberto,
vim /etc/sysconfig/networking/devices/ifcfg-eth0
John
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - Send 10MB messages!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 12:16:50 UTC
Permalink
Hi Andrea,

Yes, my ifconfig eth0 is fine and the network service is up... see below
my log and dmesg... maybe it will help to debug ? Thanks a lot for your
help.


Alberto

**********

[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)


[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/network
ls: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# cd /etc/rc.
rc.d rc.local rc.sysinit
[root at tryps network-scripts]# cd /etc/rc.d/
[root at tryps rc.d]# ls
init.d rc0.d rc2.d rc4.d rc6.d rc.sysinit
rc rc1.d rc3.d rc5.d rc.local
[root at tryps rc.d]# cd init.d/
[root at tryps init.d]# ls
acpid firstboot lisa nscd rpcidmapd tux
aep1000 functions mdmonitor ntpd rpcsvcgssd
vncserver
anacron gpm mdmpd pcmcia saslauthd winbind
apmd halt messagebus portmap sendmail xfs
atd httpd microcode_ctl postgresql single xinetd
autofs iptables named psacct smartd ypbind
bcm5820 irda netdump random smb
yppasswdd
cpuspeed irqbalance netfs rawdevices snmpd ypserv
crond isdn netplugd readahead snmptrapd ypxfrd
cups kdcrotate network readahead_early squid yum
dc_client killall nfs rhnsd sshd
dc_server kudzu nfslock rpcgssd syslog
[root at tryps init.d]# network status
bash: network: command not found
[root at tryps init.d]# ./network status
Configured devices:
lo eth0
Currently active devices:
lo eth0

*****************

[root at tryps rc.d]# dmesg
6>usbcore: registered new driver hub
ACPI: No IRQ known for interrupt pin D of device 0000:00:1f.2
ACPI: No IRQ known for interrupt pin C of device 0000:00:1f.4
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.5
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.6
ACPI: No IRQ known for interrupt pin A of device 0000:01:00.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:0c.0 - using IRQ
255
ACPI: No IRQ known for interrupt pin A of device 0000:02:0d.0 - using IRQ
255
ACPI: No IRQ known for interrupt pin B of device 0000:02:0d.1 - using IRQ
255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1090393548.4294966196:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (off)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (47 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset, but could not find the secondary
device.
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.6
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH2M: IDE controller at PCI slot 0000:00:1f.1
ICH2M: chipset revision 3
ICH2M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcff0-0xcff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcff8-0xcfff, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK6021GAS, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-R2002, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S4bios S5)
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 186k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 1343573
ext3_orphan_cleanup: deleting unreferenced inode 1343572
ext3_orphan_cleanup: deleting unreferenced inode 1343571
ext3_orphan_cleanup: deleting unreferenced inode 1343565
ext3_orphan_cleanup: deleting unreferenced inode 1343562
ext3_orphan_cleanup: deleting unreferenced inode 1343560
ext3_orphan_cleanup: deleting unreferenced inode 1343555
ext3_orphan_cleanup: deleting unreferenced inode 5195601
ext3_orphan_cleanup: deleting unreferenced inode 5195600
ext3_orphan_cleanup: deleting unreferenced inode 5195599
EXT3-fs: hda3: 10 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 144k freed
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
NET: Registered protocol family 10
Disabled Privacy Extensions on device 022db720(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
USB Universal Host Controller Interface driver v2.2
ACPI: No IRQ known for interrupt pin D of device 0000:00:1f.2
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000cf80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: No IRQ known for interrupt pin C of device 0000:00:1f.4
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 11, io base 0000cf60
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
EXT3 FS on hda3, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
cdrom: open failed.
Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.13 <tigran at veritas.com>
microcode: No suitable data for cpu 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
SCSI subsystem initialized
inserting floppy driver for 2.6.5-1.358
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
e100: Intel(R) PRO/100 Network Driver, 3.0.17
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
divert: allocating divert_blk for eth0
e100: eth0: e100_probe: addr 0xf7dff000, irq 11, MAC addr
00:00:39:DE:29:3F
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4091 buckets, 32728 max) - 296 bytes per
conntrack
e100: Intel(R) PRO/100 Network Driver, 3.0.17
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
divert: allocating divert_blk for eth0
e100: eth0: e100_probe: addr 0xf7dff000, irq 11, MAC addr
00:00:39:DE:29:3F
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:0c.0 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin A of device 0000:02:0c.0 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0c.0 [12a3:ab01]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:0c.0, mfunc 0x01000002, devctl 0x60
Yenta: request_irq() in yenta_probe_cb_irq() failed!
Yenta TI: socket 0000:02:0c.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000011
PCI: Enabling device 0000:02:0d.0 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin A of device 0000:02:0d.0 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0d.0 [1179:0001]
irq 11: nobody cared! (screaming interrupt?)
Call Trace:
[<021070c9>] __report_bad_irq+0x2b/0x67
[<02107161>] note_interrupt+0x43/0x66
[<02107327>] do_IRQ+0x109/0x169
[<0211af64>] __do_softirq+0x2c/0x73
[<021078f5>] do_softirq+0x46/0x4d
=======================
[<0210737b>] do_IRQ+0x15d/0x169
[<0210fe94>] delay_pmtmr+0xd/0x13
[<02191439>] __delay+0x9/0xa
[<2298c7fe>] yenta_probe_irq+0xa7/0x100 [yenta_socket]
[<2298c9a6>] yenta_get_socket_capabilities+0x28/0x49 [yenta_socket]
[<2298cc51>] yenta_probe+0x18c/0x1d1 [yenta_socket]
[<0219653a>] pci_device_probe_static+0x2a/0x3d
[<02196568>] __pci_device_probe+0x1b/0x2c
[<02196594>] pci_device_probe+0x1b/0x2d
[<021d94ed>] bus_match+0x27/0x45
[<021d95b9>] driver_attach+0x37/0x6a
[<021d97cb>] bus_add_driver+0x6a/0x81
[<021d9ab3>] driver_register+0x28/0x2c
[<021966b9>] pci_register_driver+0x4b/0x66
[<02127eac>] sys_init_module+0xe7/0x1bd

handlers:
[<0221522d>] (usb_hcd_irq+0x0/0x4b)
[<0221522d>] (usb_hcd_irq+0x0/0x4b)
[<22984c6e>] (e100_intr+0x0/0xe0 [e100])
Disabling IRQ #11
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000007
PCI: Enabling device 0000:02:0d.1 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin B of device 0000:02:0d.1 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0d.1 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and
others)
orinoco_cs: RequestIRQ: Resource in use
eth0: no IPv6 routers present
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
MC'97 1 converters and GPIO not ready (0xf200)
intel8x0_measure_ac97_clock: measured 49495 usecs
intel8x0: clocking to 48000
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
floppy0: data CRC error: track 0, head 0, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
end_request: I/O error, dev fd0, sector 33
Buffer I/O error on device fd0, logical block 4
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
File system has been set read-only
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Disabled Privacy Extensions on device 022db720(lo)
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
Post by Andrea Marin
#ifconfig eth0
what happen?
If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.
But the service network is started?
/etc/rc.c/init.d/network status
the answer maybe is like this
lo eth0
lo eth0
If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
/etc/rc.c/init.d/network start
Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.
Bye Andrea
Post by Alberto M R Davila
Thanks Andrea,
# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no
[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - 100MB free storage!
http://promotions.yahoo.com/new_mail
Andrea Marin
2004-07-21 12:36:11 UTC
Permalink
I see that you have the ipV4 and ipV6 in the same interface "eth0" I'm
not an expert but I think that this is one problem

inet addr:XXX.XXX.XXX.XXX
inet6 addr: fe80::200:39ff:fede:293f/64

you can try to put in your "ifcfg-eth0" file only this option including
your first line

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=XX:XX:XX:XX:XX:XX
IPADDR=XXX.XXX.XXX.XXX
NETMASK=XXX.XXX.XXX.XXX
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet



I understand that you have a laptop, if you have a pcmcia network-card
you must check if your card is support to linux because I have a laptop
whit a Allied Telesyn 2800TX pcmcia-card that is configured in the
/etc/sysconfig/netywork-script/ifcfg-eth0 and when I lunch the script
./network status everything is good but she doesn't work because she
isn't support whit the linux.

Bye Andrea
Post by Alberto M R Davila
Hi Andrea,
Yes, my ifconfig eth0 is fine and the network service is up... see below
my log and dmesg... maybe it will help to debug ? Thanks a lot for your
help.
Alberto
**********
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/network
ls: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# cd /etc/rc.
rc.d rc.local rc.sysinit
[root at tryps network-scripts]# cd /etc/rc.d/
[root at tryps rc.d]# ls
init.d rc0.d rc2.d rc4.d rc6.d rc.sysinit
rc rc1.d rc3.d rc5.d rc.local
[root at tryps rc.d]# cd init.d/
[root at tryps init.d]# ls
acpid firstboot lisa nscd rpcidmapd tux
aep1000 functions mdmonitor ntpd rpcsvcgssd
vncserver
anacron gpm mdmpd pcmcia saslauthd winbind
apmd halt messagebus portmap sendmail xfs
atd httpd microcode_ctl postgresql single xinetd
autofs iptables named psacct smartd ypbind
bcm5820 irda netdump random smb
yppasswdd
cpuspeed irqbalance netfs rawdevices snmpd ypserv
crond isdn netplugd readahead snmptrapd ypxfrd
cups kdcrotate network readahead_early squid yum
dc_client killall nfs rhnsd sshd
dc_server kudzu nfslock rpcgssd syslog
[root at tryps init.d]# network status
bash: network: command not found
[root at tryps init.d]# ./network status
lo eth0
lo eth0
Martin Schmiderer
2004-07-21 12:37:24 UTC
Permalink
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.

try: ifconfig eth0 192.168.0.100 up
Post by Alberto M R Davila
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right


greetz,

Martin
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
Andrea Marin
2004-07-21 12:36:11 UTC
Permalink
I see that you have the ipV4 and ipV6 in the same interface "eth0" I'm
not an expert but I think that this is one problem

inet addr:XXX.XXX.XXX.XXX
inet6 addr: fe80::200:39ff:fede:293f/64

you can try to put in your "ifcfg-eth0" file only this option including
your first line

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=XX:XX:XX:XX:XX:XX
IPADDR=XXX.XXX.XXX.XXX
NETMASK=XXX.XXX.XXX.XXX
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet



I understand that you have a laptop, if you have a pcmcia network-card
you must check if your card is support to linux because I have a laptop
whit a Allied Telesyn 2800TX pcmcia-card that is configured in the
/etc/sysconfig/netywork-script/ifcfg-eth0 and when I lunch the script
./network status everything is good but she doesn't work because she
isn't support whit the linux.

Bye Andrea
Post by Alberto M R Davila
Hi Andrea,
Yes, my ifconfig eth0 is fine and the network service is up... see below
my log and dmesg... maybe it will help to debug ? Thanks a lot for your
help.
Alberto
**********
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/network
ls: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# cd /etc/rc.
rc.d rc.local rc.sysinit
[root at tryps network-scripts]# cd /etc/rc.d/
[root at tryps rc.d]# ls
init.d rc0.d rc2.d rc4.d rc6.d rc.sysinit
rc rc1.d rc3.d rc5.d rc.local
[root at tryps rc.d]# cd init.d/
[root at tryps init.d]# ls
acpid firstboot lisa nscd rpcidmapd tux
aep1000 functions mdmonitor ntpd rpcsvcgssd
vncserver
anacron gpm mdmpd pcmcia saslauthd winbind
apmd halt messagebus portmap sendmail xfs
atd httpd microcode_ctl postgresql single xinetd
autofs iptables named psacct smartd ypbind
bcm5820 irda netdump random smb
yppasswdd
cpuspeed irqbalance netfs rawdevices snmpd ypserv
crond isdn netplugd readahead snmptrapd ypxfrd
cups kdcrotate network readahead_early squid yum
dc_client killall nfs rhnsd sshd
dc_server kudzu nfslock rpcgssd syslog
[root at tryps init.d]# network status
bash: network: command not found
[root at tryps init.d]# ./network status
lo eth0
lo eth0
Martin Schmiderer
2004-07-21 12:37:24 UTC
Permalink
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.

try: ifconfig eth0 192.168.0.100 up
Post by Alberto M R Davila
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right


greetz,

Martin
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
Alberto M R Davila
2004-07-21 12:53:35 UTC
Permalink
Hi Martin,
Post by Andrea Marin
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.
Network is up and configured with appropriate IP, netmask and gateway
addresses.
Post by Andrea Marin
try: ifconfig eth0 192.168.0.100 up
Post by Alberto M R Davila
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
I did with my own IP and also the one you mentioned ;-), then nothing
happened.
Post by Andrea Marin
Post by Alberto M R Davila
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right
You are right.

Is there anything in my dmesg log that could help to debug it ? I am a
normal user, then any further expert opinion would be greatly appreciated.
I cannot work without my laptop connected to the Internet :-(

Andrea: I tested your option, it did not work. I keep getting "inet6" in
my "ifconfig etho" log.

Alberto
Post by Andrea Marin
greetz,
Martin
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
antonio montagnani
2004-07-21 12:57:47 UTC
Permalink
Alberto M R Davila wrote/ha scritto, On/il 21/07/2004 14:53:

I am not sure, but is it correct line HWADDR = xxxxxxxxx in that
position?? where does it come from, since i have not that line in both
my Ethernet cards scripts???
--
Antonio

================================================
Working with Mozilla 1.7 on Linux Fedora Core 2
================================================
Utilizzo Mozilla 1.7 su Linux Fedora Core 2
================================================
Martin Schmiderer
2004-07-21 13:13:03 UTC
Permalink
Hi,
Post by Alberto M R Davila
Hi Martin,
Post by Andrea Marin
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.
Network is up and configured with appropriate IP, netmask and gateway
addresses.
try ping <your ip address>

and post the output from /etc/resolv.conf

and please, let us show the original output from ifconfig eth0 without
XXX...

it's easier to debug if we know the right ipaddress
Post by Alberto M R Davila
I did with my own IP and also the one you mentioned ;-), then nothing
happened.
Post by Andrea Marin
Post by Alberto M R Davila
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right
You are right.
greetz,

Martin

Ps: please, no pm... i read the list :)
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
Martin Schmiderer
2004-07-21 13:25:41 UTC
Permalink
Post by Martin Schmiderer
and post the output from /etc/resolv.conf
sorry, i mean cat /etc/resolv.conf
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
Martin Schmiderer
2004-07-21 13:25:41 UTC
Permalink
Post by Martin Schmiderer
and post the output from /etc/resolv.conf
sorry, i mean cat /etc/resolv.conf
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
antonio montagnani
2004-07-21 12:57:47 UTC
Permalink
Alberto M R Davila wrote/ha scritto, On/il 21/07/2004 14:53:

I am not sure, but is it correct line HWADDR = xxxxxxxxx in that
position?? where does it come from, since i have not that line in both
my Ethernet cards scripts???
--
Antonio

================================================
Working with Mozilla 1.7 on Linux Fedora Core 2
================================================
Utilizzo Mozilla 1.7 su Linux Fedora Core 2
================================================
Martin Schmiderer
2004-07-21 13:13:03 UTC
Permalink
Hi,
Post by Alberto M R Davila
Hi Martin,
Post by Andrea Marin
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.
Network is up and configured with appropriate IP, netmask and gateway
addresses.
try ping <your ip address>

and post the output from /etc/resolv.conf

and please, let us show the original output from ifconfig eth0 without
XXX...

it's easier to debug if we know the right ipaddress
Post by Alberto M R Davila
I did with my own IP and also the one you mentioned ;-), then nothing
happened.
Post by Andrea Marin
Post by Alberto M R Davila
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right
You are right.
greetz,

Martin

Ps: please, no pm... i read the list :)
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
Scot L. Harris
2004-07-21 14:37:11 UTC
Permalink
Hi Scott,
I am using the normal network cable (the blue one) to connect my card to
the local network... I just unplugged the cable/connector from a computer
connedt to internet (working properly of course) use it for my laptop and
cloned the accordingly the IP address and DNS, then nothing.. I am
attaching the log...
What a difficult task.
Thanks, Alberto
hmmm, still don't know what type of switch you are connecting to. If
you used the same IP address as another device that was on the network
there could a couple of issues even if the other device is off the
network.

The switches used at your location could be locked down. Some switches
allow you to specify what MAC address that port on the switch is allowed
to talk to. If that is the case you will need to get the network
administrator to setup a port for you on the switch.

The other problem could be that the default gateway probably has the
other machines MAC address in cache. Until that times out or can be
flushed your machine will not be able to talk to the gateway. What
happens is your system arps for the router and gets a reply. You then
try to send a packet to the MAC address supplied in the arp. The router
gets your packet and checks its arp cache for the MAC address assigned
to that IP and sends the reply out to the wrong MAC address.

Again if that is the case you can get the network administrator to flush
the arp cache or sometimes just try to ping your IP from the router.
After that it should work.

The other thing you can do is get a different IP address, one that has
not been used yet on the network.

Also, you may still want to get a cross over cable and try that test I
suggested. That will tell you for sure if the interface is configured
correctly.

Also, the other thing I mentioned last time was to verify that you do
have link to the switch (should have an led on the switch to indicate
that) and that you are set to the correct speed and duplex settings.
Those should be autonegotiated but I have seen that fail on Cisco
switches and Sun servers. You can use mii-tool to specify those
settings if needed.

I am copying this back to the list as this may provide some others with
info that may point to a solution for you.
--
Scot L. Harris
webid at cfl.rr.com

It seems a little silly now, but this country was founded as a protest
against taxation.
Bob Chiodini
2004-07-21 15:25:10 UTC
Permalink
Post by Scot L. Harris
Hi Scott,
I am using the normal network cable (the blue one) to connect my card to
the local network... I just unplugged the cable/connector from a computer
connedt to internet (working properly of course) use it for my laptop and
cloned the accordingly the IP address and DNS, then nothing.. I am
attaching the log...
What a difficult task.
Thanks, Alberto
hmmm, still don't know what type of switch you are connecting to. If
you used the same IP address as another device that was on the network
there could a couple of issues even if the other device is off the
network.
The switches used at your location could be locked down. Some switches
allow you to specify what MAC address that port on the switch is allowed
to talk to. If that is the case you will need to get the network
administrator to setup a port for you on the switch.
The other problem could be that the default gateway probably has the
other machines MAC address in cache. Until that times out or can be
flushed your machine will not be able to talk to the gateway. What
happens is your system arps for the router and gets a reply. You then
try to send a packet to the MAC address supplied in the arp. The router
gets your packet and checks its arp cache for the MAC address assigned
to that IP and sends the reply out to the wrong MAC address.
Again if that is the case you can get the network administrator to flush
the arp cache or sometimes just try to ping your IP from the router.
After that it should work.
The other thing you can do is get a different IP address, one that has
not been used yet on the network.
Also, you may still want to get a cross over cable and try that test I
suggested. That will tell you for sure if the interface is configured
correctly.
Also, the other thing I mentioned last time was to verify that you do
have link to the switch (should have an led on the switch to indicate
that) and that you are set to the correct speed and duplex settings.
Those should be autonegotiated but I have seen that fail on Cisco
switches and Sun servers. You can use mii-tool to specify those
settings if needed.
I am copying this back to the list as this may provide some others with
info that may point to a solution for you.
--
Scot L. Harris
webid at cfl.rr.com
It seems a little silly now, but this country was founded as a protest
against taxation.
If you can't ping from the router: This will flush the old ARP cache
entry on some Cisco Routers. I have not tried it on anything else:

ping -q -c 1 -b -I $COMMONIP $NETWORK

Where $COMMONIP is the IP address of the interface to ping from and
$NETWORK is the network address of your subnet.

Bob...
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: This is a digitally signed message part
Url : http://lists.fedoraproject.org/pipermail/users/attachments/20040721/57043a22/attachment.bin
Bob Chiodini
2004-07-21 15:25:10 UTC
Permalink
Post by Scot L. Harris
Hi Scott,
I am using the normal network cable (the blue one) to connect my card to
the local network... I just unplugged the cable/connector from a computer
connedt to internet (working properly of course) use it for my laptop and
cloned the accordingly the IP address and DNS, then nothing.. I am
attaching the log...
What a difficult task.
Thanks, Alberto
hmmm, still don't know what type of switch you are connecting to. If
you used the same IP address as another device that was on the network
there could a couple of issues even if the other device is off the
network.
The switches used at your location could be locked down. Some switches
allow you to specify what MAC address that port on the switch is allowed
to talk to. If that is the case you will need to get the network
administrator to setup a port for you on the switch.
The other problem could be that the default gateway probably has the
other machines MAC address in cache. Until that times out or can be
flushed your machine will not be able to talk to the gateway. What
happens is your system arps for the router and gets a reply. You then
try to send a packet to the MAC address supplied in the arp. The router
gets your packet and checks its arp cache for the MAC address assigned
to that IP and sends the reply out to the wrong MAC address.
Again if that is the case you can get the network administrator to flush
the arp cache or sometimes just try to ping your IP from the router.
After that it should work.
The other thing you can do is get a different IP address, one that has
not been used yet on the network.
Also, you may still want to get a cross over cable and try that test I
suggested. That will tell you for sure if the interface is configured
correctly.
Also, the other thing I mentioned last time was to verify that you do
have link to the switch (should have an led on the switch to indicate
that) and that you are set to the correct speed and duplex settings.
Those should be autonegotiated but I have seen that fail on Cisco
switches and Sun servers. You can use mii-tool to specify those
settings if needed.
I am copying this back to the list as this may provide some others with
info that may point to a solution for you.
--
Scot L. Harris
webid at cfl.rr.com
It seems a little silly now, but this country was founded as a protest
against taxation.
If you can't ping from the router: This will flush the old ARP cache
entry on some Cisco Routers. I have not tried it on anything else:

ping -q -c 1 -b -I $COMMONIP $NETWORK

Where $COMMONIP is the IP address of the interface to ping from and
$NETWORK is the network address of your subnet.

Bob...
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: This is a digitally signed message part
Url : http://lists.fedoraproject.org/pipermail/users/attachments/20040721/57043a22/attachment-0002.bin
Alberto M R Davila
2004-07-21 17:16:41 UTC
Permalink
Post by Alberto M R Davila
Post by John Morrison
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by John Morrison
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by John Morrison
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
Something simple. Does your netmask match the network netmask?
Hi, I am not an expert.. so, how I should check this in FC2 ?

Thanks, Alberto



__________________________________
Do you Yahoo!?
Yahoo! Mail Address AutoComplete - You start. We finish.
http://promotions.yahoo.com/new_mail
Dattatraya
2004-07-21 18:45:01 UTC
Permalink
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...

Dattatraya
--
-------------------------------------------------------------------------------------------
Half of courage is having done the thing before. ---- Ralph Waldo Emerson
Dattatraya
2004-07-21 18:45:01 UTC
Permalink
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...

Dattatraya
--
-------------------------------------------------------------------------------------------
Half of courage is having done the thing before. ---- Ralph Waldo Emerson
Alberto M R Davila
2004-07-21 18:57:18 UTC
Permalink
Post by Dattatraya
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0
is
Post by Alberto M R Davila
Post by Alberto M R Davila
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
Post by Alberto M R Davila
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was
using
Post by Alberto M R Davila
Post by Alberto M R Davila
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...
Dattatraya
--
-------------------------------------------------------------------------------------------
Post by Dattatraya
Half of courage is having done the thing before. ---- Ralph Waldo
Emerson
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
Alberto M R Davila
2004-07-21 19:06:55 UTC
Permalink
Post by Dattatraya
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0
is
Post by Alberto M R Davila
Post by Alberto M R Davila
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
Post by Alberto M R Davila
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was
using
Post by Alberto M R Davila
Post by Alberto M R Davila
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...
Dattatraya
I stopped the iptables service and also disable my firewall, nothing
happened... I cannot connect to Internet.. will try the Scot suggestions.

Cheers, Alberto




__________________________________
Do you Yahoo!?
Yahoo! Mail is new and improved - Check it out!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 01:37:32 UTC
Permalink
Yes, I use static IP address and not DHCP... I was using FC1 nicely (with
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should run
nice as well... :-(

Will try your suggestion in case I don?t get any further useful tips.

Thanks, Alberto
Hey,
--my 2 cents--
I'm assuming that you dont have dhcp setup for that, which makes
sense. I jumped over to the toshiba satellite and the 4600 isnt sold
anymore (least I didnt see it in the product area of their website).
First thing I would probably do *I'm no expert, but I can get things
done* is go here http://www.lnxbbc.com/ and d/l that little 50meg
distro that runs from cd. It has a simple network setup utility and
if it can get you connected you know its just a setting in fedoracore.
I'd really have to know more about the actual hardware to help you
anymore. Dont know if this will help you any.
-Matt
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
__________________________________
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
http://promotions.yahoo.com/new_mail
--
fedora-list mailing list
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - Send 10MB messages!
http://promotions.yahoo.com/new_mail
John Morrison
2004-07-21 08:10:15 UTC
Permalink
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3) and
the ethernet card is not working even the "redhat-config-network" shows
eth0 is "Active"... I tried a new installation (formatting partitions)
but it does not work as well... curiously during boot the eth0 is loaded
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled to
allow only SSH connections... btw, my sound card was not recognized after
installation as well, the test failed... any tips how I could conifgure
the eth0 manually ? Everything used to work fine when I was using FC1 in
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,

I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.

--
John
Alberto M R Davila
2004-07-21 10:11:17 UTC
Permalink
Hi,

The "network device control" is like this:

Status Device Nickname
Active eth0 eth0

Looks OK but does * not * work ... how I could configure manually ?

Thanks, Alberto
Post by Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0 works...
"ping" from and to the laptop does not work. My "firewall" is enabled
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using FC1
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 10:39:14 UTC
Permalink
Hi,

Good and bad to know I am not alone ! ;-)

I just checked my /etc/sysconfig/hwconf:

class: NETWORK
bus: PCI
detached: 0
device: eth0
driver: e100
desc: "Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller"
network.hwaddr: 00:00:39:DE:29:3F
vendorId: 8086
deviceId: 2449
subVendorId: 8086
subDeviceId: 3013
pciType: 1
pcidom: 0
pcibus: 2
pcidev: 8
pcifn: 0
-

-
class: NETWORK
bus: PCMCIA
detached: 96
device: eth1
driver: orinoco_cs
desc: "Intersil PRISM2 11 Mbps Wireless Adapter"
vendorId: 0156
deviceId: 0002
function: 0
slot: 0

Again apparently looks OK, unless the real experts let me know about any
problems.

I am missing my FC1 now, without eth0 up and working I cannot do my stuff.

Thanks for any further tips you may send.

Cheers, Alberto
Post by James A. Giseburt
Good Day!
I also have a Toshiba Satellite Pro 4600. As you stated, everything
worked well with FC1. Not so with FC2.
I am not having your problem with eth0 (the built-in ethernet adapter).
I do have an alias in /etc/modprobe.conf for that adapter (alias eth0
e100), but other than that it works.
I am also having the problems that you describe with sound. I haven't
been able to figure that out yet. I've checked all of the sound
settings that I can find and I'm still looking. At this point, it would
be nice to hear a simple beep, let alone music or some other audio.
My only other problem is that my Cisco Aironet 350 PC Card doesn't
work. It worked in FC1, but I haven't been able to get it to work with
FC2. The system recognizes the card, but I haven't been able to
activate the interface. I'm stumped at this point. Other people say
that they have gotten this card to work, but not me. I've resorted to
an old D-Link card (it pops right up).
Sorry I haven't been of any help, but I just wanted to let you know that
you are not alone.
Jim
James A. Giseburt
Information Systems Manager E-mail: giseburt at molineschools.org
Moline School District No. 40 Voice : 309.743.8990
2515 - 41st Street Fax : 309.743.8996
Moline, IL 61265 Web : http://www.molineschools.org
Post by Alberto M R Davila
Yes, I use static IP address and not DHCP... I was using FC1 nicely
(with
Post by Alberto M R Davila
my 512MB RAM and 60Gb HD) then assumed FC2 and its kernel 2.6 should
run
Post by Alberto M R Davila
nice as well... :-(
On Tue, 20 Jul 2004 17:56:30 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium
3)
Post by Alberto M R Davila
and
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by Alberto M R Davila
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled
Post by Alberto M R Davila
to
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
after
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1
Post by Alberto M R Davila
in
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
Alberto M R Davila
2004-07-21 11:14:25 UTC
Permalink
Thanks Andrea,

My "ifcfg-eth0" is like this:

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no

When I "ping" to a machine in the intranet I got this:

[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
--- LOCAL.MACHINE ping statistics ---
10 packets transmitted, 0 received, +9 errors, 100% packet loss, time
8998ms
, pipe 5:

In other words, it is not working yet :-(

Any further tips ?

Thanks, Alberto
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0" and
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - 100MB free storage!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 11:31:04 UTC
Permalink
Hi John,

It is exactly as in /etc/sysconfig/network-scripts:

# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no

Should I try a source (which one ?) from fedora site and try a fresh
installation by "make" and "make install" ?

Thanks, Alberto
Post by John Morrison
Post by Andrea Marin
Hi Alberto,
you can configure all your network-interface in
/etc/sysconfig/network-script.
In this folder probably you will find more file for more
networks-interface that your system have.
For configure the eth0 interface you must edit the file "ifcfg-eth0"
and
Post by Andrea Marin
in this file you can write all your option
# Silicon Integrated Systems [SiS]|SiS900 PCI Fast Ethernet
DEVICE=eth0 //This is the name
BOOTPROTO=static //This is the boot protocol static/dhcp
BROADCAST=XXX.XXX.XXX.XXX //IP addr
HWADDR=XX:XX:XX:XX:XX:XX //IP addr
IPADDR=XXX.XXX.XXX.XXX //IP addr
NETMASK=XXX.XXX.XXX.XXX //IP addr
NETWORK=XXX.XXX.XXX.XXX //IP addr
ONBOOT=yes //if is activate on boot or not
TYPE=Ethernet //type of the layer 2 protocol
Bye Andrea
Post by Alberto M R Davila
Hi,
Status Device Nickname
Active eth0 eth0
Looks OK but does * not * work ... how I could configure manually ?
Thanks, Alberto
Alberto,
vim /etc/sysconfig/networking/devices/ifcfg-eth0
John
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - Send 10MB messages!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 12:16:50 UTC
Permalink
Hi Andrea,

Yes, my ifconfig eth0 is fine and the network service is up... see below
my log and dmesg... maybe it will help to debug ? Thanks a lot for your
help.


Alberto

**********

[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)


[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/network
ls: /etc/rc.c/init.d/network: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# ls /etc/rc.c/init.d/
ls: /etc/rc.c/init.d/: No such file or directory
[root at tryps network-scripts]# cd /etc/rc.
rc.d rc.local rc.sysinit
[root at tryps network-scripts]# cd /etc/rc.d/
[root at tryps rc.d]# ls
init.d rc0.d rc2.d rc4.d rc6.d rc.sysinit
rc rc1.d rc3.d rc5.d rc.local
[root at tryps rc.d]# cd init.d/
[root at tryps init.d]# ls
acpid firstboot lisa nscd rpcidmapd tux
aep1000 functions mdmonitor ntpd rpcsvcgssd
vncserver
anacron gpm mdmpd pcmcia saslauthd winbind
apmd halt messagebus portmap sendmail xfs
atd httpd microcode_ctl postgresql single xinetd
autofs iptables named psacct smartd ypbind
bcm5820 irda netdump random smb
yppasswdd
cpuspeed irqbalance netfs rawdevices snmpd ypserv
crond isdn netplugd readahead snmptrapd ypxfrd
cups kdcrotate network readahead_early squid yum
dc_client killall nfs rhnsd sshd
dc_server kudzu nfslock rpcgssd syslog
[root at tryps init.d]# network status
bash: network: command not found
[root at tryps init.d]# ./network status
Configured devices:
lo eth0
Currently active devices:
lo eth0

*****************

[root at tryps rc.d]# dmesg
6>usbcore: registered new driver hub
ACPI: No IRQ known for interrupt pin D of device 0000:00:1f.2
ACPI: No IRQ known for interrupt pin C of device 0000:00:1f.4
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.5
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.6
ACPI: No IRQ known for interrupt pin A of device 0000:01:00.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
ACPI: No IRQ known for interrupt pin A of device 0000:02:0c.0 - using IRQ
255
ACPI: No IRQ known for interrupt pin A of device 0000:02:0d.0 - using IRQ
255
ACPI: No IRQ known for interrupt pin B of device 0000:02:0d.1 - using IRQ
255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1090393548.4294966196:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (off)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (47 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset, but could not find the secondary
device.
agpgart: Detected an Intel i815 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 64M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.6
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH2M: IDE controller at PCI slot 0000:00:1f.1
ICH2M: chipset revision 3
ICH2M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcff0-0xcff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcff8-0xcfff, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK6021GAS, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-R2002, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S4bios S5)
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 186k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 1343573
ext3_orphan_cleanup: deleting unreferenced inode 1343572
ext3_orphan_cleanup: deleting unreferenced inode 1343571
ext3_orphan_cleanup: deleting unreferenced inode 1343565
ext3_orphan_cleanup: deleting unreferenced inode 1343562
ext3_orphan_cleanup: deleting unreferenced inode 1343560
ext3_orphan_cleanup: deleting unreferenced inode 1343555
ext3_orphan_cleanup: deleting unreferenced inode 5195601
ext3_orphan_cleanup: deleting unreferenced inode 5195600
ext3_orphan_cleanup: deleting unreferenced inode 5195599
EXT3-fs: hda3: 10 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 144k freed
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
NET: Registered protocol family 10
Disabled Privacy Extensions on device 022db720(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
USB Universal Host Controller Interface driver v2.2
ACPI: No IRQ known for interrupt pin D of device 0000:00:1f.2
uhci_hcd 0000:00:1f.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 11, io base 0000cf80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: No IRQ known for interrupt pin C of device 0000:00:1f.4
uhci_hcd 0000:00:1f.4: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 11, io base 0000cf60
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
EXT3 FS on hda3, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
cdrom: open failed.
Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.13 <tigran at veritas.com>
microcode: No suitable data for cpu 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
SCSI subsystem initialized
inserting floppy driver for 2.6.5-1.358
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
e100: Intel(R) PRO/100 Network Driver, 3.0.17
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
divert: allocating divert_blk for eth0
e100: eth0: e100_probe: addr 0xf7dff000, irq 11, MAC addr
00:00:39:DE:29:3F
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4091 buckets, 32728 max) - 296 bytes per
conntrack
e100: Intel(R) PRO/100 Network Driver, 3.0.17
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: No IRQ known for interrupt pin A of device 0000:02:08.0
divert: allocating divert_blk for eth0
e100: eth0: e100_probe: addr 0xf7dff000, irq 11, MAC addr
00:00:39:DE:29:3F
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:0c.0 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin A of device 0000:02:0c.0 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0c.0 [12a3:ab01]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:0c.0, mfunc 0x01000002, devctl 0x60
Yenta: request_irq() in yenta_probe_cb_irq() failed!
Yenta TI: socket 0000:02:0c.0 no PCI interrupts. Fish. Please report.
Yenta: ISA IRQ mask 0x0000, PCI irq 0
Socket status: 30000011
PCI: Enabling device 0000:02:0d.0 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin A of device 0000:02:0d.0 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0d.0 [1179:0001]
irq 11: nobody cared! (screaming interrupt?)
Call Trace:
[<021070c9>] __report_bad_irq+0x2b/0x67
[<02107161>] note_interrupt+0x43/0x66
[<02107327>] do_IRQ+0x109/0x169
[<0211af64>] __do_softirq+0x2c/0x73
[<021078f5>] do_softirq+0x46/0x4d
=======================
[<0210737b>] do_IRQ+0x15d/0x169
[<0210fe94>] delay_pmtmr+0xd/0x13
[<02191439>] __delay+0x9/0xa
[<2298c7fe>] yenta_probe_irq+0xa7/0x100 [yenta_socket]
[<2298c9a6>] yenta_get_socket_capabilities+0x28/0x49 [yenta_socket]
[<2298cc51>] yenta_probe+0x18c/0x1d1 [yenta_socket]
[<0219653a>] pci_device_probe_static+0x2a/0x3d
[<02196568>] __pci_device_probe+0x1b/0x2c
[<02196594>] pci_device_probe+0x1b/0x2d
[<021d94ed>] bus_match+0x27/0x45
[<021d95b9>] driver_attach+0x37/0x6a
[<021d97cb>] bus_add_driver+0x6a/0x81
[<021d9ab3>] driver_register+0x28/0x2c
[<021966b9>] pci_register_driver+0x4b/0x66
[<02127eac>] sys_init_module+0xe7/0x1bd

handlers:
[<0221522d>] (usb_hcd_irq+0x0/0x4b)
[<0221522d>] (usb_hcd_irq+0x0/0x4b)
[<22984c6e>] (e100_intr+0x0/0xe0 [e100])
Disabling IRQ #11
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000007
PCI: Enabling device 0000:02:0d.1 (0000 -> 0002)
ACPI: No IRQ known for interrupt pin B of device 0000:02:0d.1 - using IRQ
255
Yenta: CardBus bridge found at 0000:02:0d.1 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes at gibson.dropbear.id.au> and
others)
orinoco_cs: RequestIRQ: Resource in use
eth0: no IPv6 routers present
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
ACPI: No IRQ known for interrupt pin B of device 0000:00:1f.5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
MC'97 1 converters and GPIO not ready (0xf200)
intel8x0_measure_ac97_clock: measured 49495 usecs
intel8x0: clocking to 48000
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
floppy0: data CRC error: track 0, head 0, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
floppy0: data CRC error: track 0, head 1, sector 16, size 2
end_request: I/O error, dev fd0, sector 33
Buffer I/O error on device fd0, logical block 4
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
File system has been set read-only
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
FAT: Filesystem panic (dev fd0)
fat_get_cluster: invalid cluster chain (i_pos 0)
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NETDEV WATCHDOG: eth0: transmit timed out
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Disabled Privacy Extensions on device 022db720(lo)
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
Post by Andrea Marin
#ifconfig eth0
what happen?
If there is your network-interface whit the same parameter for the
ip-address and mac-address is right.
But the service network is started?
/etc/rc.c/init.d/network status
the answer maybe is like this
lo eth0
lo eth0
If is like this is right, if in the Currently active devices there is
only the loopback-interface it seams that your network is down and you
/etc/rc.c/init.d/network start
Now you can try to ping yourself whit the IP-Address of your intranet
and after you can try to ping the other machines.
Bye Andrea
Post by Alberto M R Davila
Thanks Andrea,
# Intel Corp.|82801BA/BAM/CA/CAM Ethernet Controller
DEVICE=eth0
BOOTPROTO=static
BROADCAST=XXX.XXX.XXX.XXX
HWADDR=00:00:39:DE:29:3F
IPADDR=XXX.XXX.XXX.XXX
NETMASK=255.255.255.0
NETWORK=XXX.XXX.XXX.XXX
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
PEERDNS=no
GATEWAY=XXX.XXX.XXX.XXX.
IPV6INIT=no
[root at tryps network-scripts]# ping LOCAL.MACHINE
PING LOCAL.MACHINE (LOCAL.MACHINE) 56(84) bytes of data.
From XXX.XXX.XXX.XXX icmp_seq=0 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=1 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=2 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=3 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=4 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=5 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=6 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=7 Destination Host Unreachable
From XXX.XXX.XXX.XXX icmp_seq=8 Destination Host Unreachable
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - 100MB free storage!
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 12:53:35 UTC
Permalink
Hi Martin,
Post by Andrea Marin
Hi Alberto
Post by Alberto M R Davila
[root at tryps network-scripts]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:39:DE:29:3F
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX
is there realy XXX.XXX.XXX.XXX in the output? if yes, you have to
configure your network.
Network is up and configured with appropriate IP, netmask and gateway
addresses.
Post by Andrea Marin
try: ifconfig eth0 192.168.0.100 up
Post by Alberto M R Davila
Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fede:293f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:406 (406.0 b)
I did with my own IP and also the one you mentioned ;-), then nothing
happened.
Post by Andrea Marin
Post by Alberto M R Davila
[root at tryps network-scripts]# /etc/rc.c/init.d/network status
bash: /etc/rc.c/init.d/network: No such file or directory
^
wrong place :) /etc/rc.d/init.d/network is right
You are right.

Is there anything in my dmesg log that could help to debug it ? I am a
normal user, then any further expert opinion would be greatly appreciated.
I cannot work without my laptop connected to the Internet :-(

Andrea: I tested your option, it did not work. I keep getting "inet6" in
my "ifconfig etho" log.

Alberto
Post by Andrea Marin
greetz,
Martin
--
Martin Schmiderer
Walbenstr. 12
72127 Wankheim
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
Scot L. Harris
2004-07-21 14:37:11 UTC
Permalink
Hi Scott,
I am using the normal network cable (the blue one) to connect my card to
the local network... I just unplugged the cable/connector from a computer
connedt to internet (working properly of course) use it for my laptop and
cloned the accordingly the IP address and DNS, then nothing.. I am
attaching the log...
What a difficult task.
Thanks, Alberto
hmmm, still don't know what type of switch you are connecting to. If
you used the same IP address as another device that was on the network
there could a couple of issues even if the other device is off the
network.

The switches used at your location could be locked down. Some switches
allow you to specify what MAC address that port on the switch is allowed
to talk to. If that is the case you will need to get the network
administrator to setup a port for you on the switch.

The other problem could be that the default gateway probably has the
other machines MAC address in cache. Until that times out or can be
flushed your machine will not be able to talk to the gateway. What
happens is your system arps for the router and gets a reply. You then
try to send a packet to the MAC address supplied in the arp. The router
gets your packet and checks its arp cache for the MAC address assigned
to that IP and sends the reply out to the wrong MAC address.

Again if that is the case you can get the network administrator to flush
the arp cache or sometimes just try to ping your IP from the router.
After that it should work.

The other thing you can do is get a different IP address, one that has
not been used yet on the network.

Also, you may still want to get a cross over cable and try that test I
suggested. That will tell you for sure if the interface is configured
correctly.

Also, the other thing I mentioned last time was to verify that you do
have link to the switch (should have an led on the switch to indicate
that) and that you are set to the correct speed and duplex settings.
Those should be autonegotiated but I have seen that fail on Cisco
switches and Sun servers. You can use mii-tool to specify those
settings if needed.

I am copying this back to the list as this may provide some others with
info that may point to a solution for you.
--
Scot L. Harris
webid at cfl.rr.com

It seems a little silly now, but this country was founded as a protest
against taxation.
Alberto M R Davila
2004-07-21 17:16:41 UTC
Permalink
Post by Alberto M R Davila
Post by John Morrison
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and
Post by John Morrison
Post by Alberto M R Davila
the ethernet card is not working even the "redhat-config-network"
shows
Post by John Morrison
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0 is
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not recognized
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was using
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
I had a problem when I first installed FC2 with ethernet cards being
given a different device name from FC1. I have two network cards and
eth0 became eth1 and vice versa. I realise that you may only have one
card but it is worth checking that the device name has not changed
somewhere. Check redhat->system tools-> network device control.
--
John
Something simple. Does your netmask match the network netmask?
Hi, I am not an expert.. so, how I should check this in FC2 ?

Thanks, Alberto



__________________________________
Do you Yahoo!?
Yahoo! Mail Address AutoComplete - You start. We finish.
http://promotions.yahoo.com/new_mail
Alberto M R Davila
2004-07-21 18:57:18 UTC
Permalink
Post by Dattatraya
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0
is
Post by Alberto M R Davila
Post by Alberto M R Davila
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
Post by Alberto M R Davila
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was
using
Post by Alberto M R Davila
Post by Alberto M R Davila
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...
Dattatraya
--
-------------------------------------------------------------------------------------------
Post by Dattatraya
Half of courage is having done the thing before. ---- Ralph Waldo
Emerson
--
fedora-list mailing list
fedora-list at redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
__________________________________
Do you Yahoo!?
Vote for the stars of Yahoo!'s next ad campaign!
http://advision.webevents.yahoo.com/yahoo/votelifeengine/
Alberto M R Davila
2004-07-21 19:06:55 UTC
Permalink
Post by Dattatraya
On Wed, 21 Jul 2004 10:16:41 -0700 (PDT), Alberto M R Davila
Post by Alberto M R Davila
I just installed FC2 in my toshiba satellite 4600 laptop (pentium 3)
and the ethernet card is not working even the "redhat-config-network"
shows
Post by Alberto M R Davila
eth0 is "Active"... I tried a new installation (formatting
Post by Alberto M R Davila
partitions)
Post by John Morrison
Post by Alberto M R Davila
but it does not work as well... curiously during boot the eth0
is
Post by Alberto M R Davila
Post by Alberto M R Davila
loaded
Post by John Morrison
Post by Alberto M R Davila
"OK". I tried the "linux rescue" boot with the disk 1 of FC2 and
nothing... but when I try the "linux rescue" of FC1 the eth0
works...
Post by John Morrison
Post by Alberto M R Davila
"ping" from and to the laptop does not work. My "firewall" is
enabled to
Post by John Morrison
Post by Alberto M R Davila
allow only SSH connections... btw, my sound card was not
recognized
Post by Alberto M R Davila
Post by Alberto M R Davila
after
Post by John Morrison
Post by Alberto M R Davila
installation as well, the test failed... any tips how I could
conifgure
Post by John Morrison
Post by Alberto M R Davila
the eth0 manually ? Everything used to work fine when I was
using
Post by Alberto M R Davila
Post by Alberto M R Davila
FC1 in
Post by John Morrison
Post by Alberto M R Davila
the same laptop ;-)
Thanks for any tips you may send.
Cheers, Alberto
Alberto,
Hi.. I'm no expert but I have a guess it might be because you have
iptables running with somw wrong config... try stopping the iptables
service completely and then try to ping.... It might just work...
Dattatraya
I stopped the iptables service and also disable my firewall, nothing
happened... I cannot connect to Internet.. will try the Scot suggestions.

Cheers, Alberto




__________________________________
Do you Yahoo!?
Yahoo! Mail is new and improved - Check it out!
http://promotions.yahoo.com/new_mail

Loading...